Ricoh AFICIO MP 6001 Troubleshooting Manual Download Page 105

Page: 105 / 160

When You Cannot Send Scanned Files

This section describes likely causes of and solutions for problems related to network delivery and sending
e-mail.

When Stored Files Cannot Be Accessed

This section describes likely causes of and possible solutions for job access-related problems.

Problem

Cause

Solution

The stored file is locked and is
not accessible.

The file, which is password
protected, is locked because
the password was incorrectly
entered ten times.

Contact the administrator.

When You Cannot Browse the Network to Send a Scan File

This section describes likely causes of and possible solutions for the network browsing failing to operate
when files are sent.

Problem

Cause

Solution

The network cannot be
browsed when specifying the
destination folder.

The following machine
settings may not be correct:

• IP address
• Subnet Mask

Check the settings. See "Interface
Settings", Network and System Settings
Guide .

When the TWAIN Driver Cannot Be Started

This section describes likely causes of and possible solutions for the TWAIN driver-related problems.

Problem

Cause

Solution

The Scanner Properties
dialog box cannot be
displayed.

Advanced encryption has
been specified in the
extended security setting.

For details about the extended security
setting, contact an administrator.

When You Cannot Send Scanned Files

103

Summary of Contents for AFICIO MP 6001
































































































































































Search results

Summary of Contents for AFICIO MP 6001

Reviews:

Related manuals for AFICIO MP 6001

Brands by name

Popular brands

Ricoh AFICIO MP 6001, Troubleshooting Manual

Search results

Summary of Contents for AFICIO MP 6001

Reviews:

Related manuals for AFICIO MP 6001

Brands by name

Popular brands