Rheem RGFE Installation Instructions Manual Download Page 2

Page: 2 / 132

IMPORTANT:

To insure proper installation and operation of this product, com-

pletely read all instructions prior to attempting to assemble, install, operate, main-

tain or repair this product. Upon unpacking of the furnace, inspect all parts for

damage prior to installation and start-up.

TABLE OF CONTENTS

SAFETY INFORMATION ..........................................................................................................................................3

INSTALLATION CHECK LIST...................................................................................................................................5

GENERAL INFORMATION .......................................................................................................................................6

IMPORTANT INFORMATION ABOUT EFFICIENCY AND INDOOR AIR QUALITY..............................................8

LOCATION REQUIREMENTS AND CONSIDERATIONS.......................................................................................9

CLEARANCE-ACCESSIBILITY....................................................................................................................10

SITE SELECTION.........................................................................................................................................11

DIMENSIONS AND CLEARANCE TO COMBUSTIBLES...........................................................................12

UPFLOW MODELS.............................................................................................................................12

DOWNFLOW MODELS......................................................................................................................13

HORIZONTAL MODELS.....................................................................................................................14

DUCTING ......................................................................................................................................................15

SUPPLY AIR SENSOR.................................................................................................................................17

VENTING AND COMBUSTION AIR PIPING .........................................................................................................18

INSTALLATION WITH PRE-EXISTING VENT SYSTEMS..........................................................................18

JOINING PIPE AND FITTINGS....................................................................................................................19

CEMENTING JOINTS...................................................................................................................................19

NON-DIRECT VENT PIPE INSTALLATION...........................................................................................................20

DIRECT VENT PIPE INSTALLATION ....................................................................................................................24

CONCENTRIC TERMINATIONS..................................................................................................................26

HORIZONTAL TERMINATIONS...................................................................................................................28

CONDENSATE DRAIN / OPTIONAL NEUTRALIZER ..........................................................................................34

CONVERTING DOWNFLOW/HORIZONTAL MODELS TO HORIZONTAL CONFIGURATION.........................36

GAS SUPPLY AND PIPING....................................................................................................................................39

GAS VALVE...................................................................................................................................................40

LP CONVERSION.........................................................................................................................................42

ELECTRICAL WIRING............................................................................................................................................45

ACCESSORIES.......................................................................................................................................................47

ELECTRONIC AIR CLEANER......................................................................................................................47

HUMIDIFICATION AND DEHUMIDIFICATION............................................................................................47

OTHER ACCESSORIES ..............................................................................................................................49

TYPICAL WIRING ACCESSORIES FOR COMMUNICATING RESIDENTIAL SYSTEMS ............49-50

HIGH ALTITUDE INSTALLATIONS ........................................................................................................................51

LP GAS AT HIGH ALTITUDE ELEVATIONS................................................................................................53

ZONING SYSTEMS......................................................................................................................................54

INSTALLATION WITH NON-COMMUNICATING, HIGH-EFFICIENCY PREMIUM COOLING

SYSTEMS ...................................................................................................................................................54

INTEGRATED FURNACE CONTROL ...................................................................................................................55

CONNECTORS AND COMPONENTS OF FURNACE CONTROL ...........................................................55

SPECIAL CONFIGURATION – COMM T-STAT AND NON-COMM CONDENSER..................................56

MEMORY CARD...........................................................................................................................................60

RULES FOR WRITING, DISTRIBUTION AND ARBITRATION OF MULTIPLE COPIES OF

FURNACE SHARED DATA FOR COMMUNICATING-CAPABLE FURNACES ..............................60

REPLACING THE FURNACE CONTROL...................................................................................................63

DIPSWITCHES .............................................................................................................................................66

FURNACE OPERATION USING NON-COMMUNICATING MODULATING,

MODULATING AND TWO-STAGE T-STATS.....................................................................................69

COMMUNICATING SYSTEMS ....................................................................................................................73

WIRING FOR COMMUNICATIONS...................................................................................................73

STARTUP FOR SYSTEMS CONFIGURED WITH COMMUNICATIONS........................................74

CONTINUOUS FAN OPERATION IN COMMUNICATING MODE...................................................75

ACTIVE FAULT CODES WITH COMMUNICATING SYSTEMS.......................................................75

FURNACE USER MENUS ...........................................................................................................................75

STATUS 1 ............................................................................................................................................76

STATUS 2............................................................................................................................................78

2 WK HIST...........................................................................................................................................78

LIFE HIST............................................................................................................................................79

FAULT HISTORY.................................................................................................................................79

UNIT INFO...........................................................................................................................................79

SETUP.................................................................................................................................................79

DIPSWITCH.........................................................................................................................................80

DUAL-FUEL OPERATION............................................................................................................................80

START-UP PROCEDURES ....................................................................................................................................81

SEQUENCE OF OPERATION .....................................................................................................................83

SETTING INPUT RATE ................................................................................................................................83

MAINTENANCE.......................................................................................................................................................84

TROUBLESHOOTING CHART ..............................................................................................................................87

NORMAL OPERATING CODES (TABLE 20) ........................................................................................................89

FURNACE FAULT CODES WITH DESCRIPTIONS AND SOLUTIONS (TABLE 21)..................................90-105

WIRE DIAGRAM – STEPPER / SERVO MODULATING VALVE (FUEL CODES HA OR HB).........................106

WIRE DIAGRAM – SOLENOID CONTROLLED MODULATING VALVE (FUEL CODES HG OR HH)............107

THERMOSTATS....................................................................................................................................................108

NON-COMMUNICATING THERMOSTATS...............................................................................................108

THERMOSTAT WIRING (WITH WIRING DIAGRAMS) ............................................................................109

APPLICATIONS.....................................................................................................................................................112

MODULATING, TOUCH-SCREEN, NON-COMMUNICATING THERMOSTAT ((-)HC-TST412MDMS) ..112

COMMUNICATING THERMOSTATS.........................................................................................................122

(-)HC-TST501CMMS PROGRAMMABLE COMMUNICATING THERMOSTAT............................124

(-)HC-TST550CMMS FULL COLOR, PROGRAMMABLE COMMUNICATING THERMOSTAT...128

Installation Instructions are updated on

a regular basis. This is done as product

changes occur or if new information

becomes available. In this publication,

an arrow

➤

denotes changes from the

previous edition or additional new

material.

IMPORTANT:

All Rheem products

meet current Federal OSHA Guidelines

for safety. California Proposition 65

warnings are required for certain prod-

ucts, which are not covered by the

OSHA standards.
California's Proposition 65 requires

warnings for products sold in California

that contain, or produce, any of over

600 listed chemicals known to the

State of California to cause cancer or

birth defects such as fiberglass insula-

tion, lead in brass, and combustion

products from natural gas.
All “new equipment” shipped for sale in

California will have labels stating that

the product contains and/or produces

Proposition 65 chemicals. Although we

have not changed our processes, hav-

ing the same label on all our products

facilitates manufacturing and shipping.

We cannot always know “when, or if”

products will be sold in the California

market.
You may receive inquiries from cus-

tomers about chemicals found in, or

produced by, some of our heating and

air-conditioning equipment, or found in

natural gas used with some of our

products. Listed below are those chem-

icals and substances commonly asso-

ciated with similar equipment in our

industry and other manufacturers.

• Glass Wool (Fiberglass) Insulation

• Carbon Monoxide (CO)

• Formaldehyde

• Benzene

More details are available at the

Websites for OSHA (Occupational

Safety and Health Administration), at

www.osha.gov and the State of

California's OEHHA (Office of

Environmental Health Hazard

Assessment), at www.oehha.org.

Consumer education is important since

the chemicals and substances on the

list are found in our daily lives. Most

consumers are aware that products

present safety and health risks, when

improperly used, handled and main-

tained.

Summary of Contents for RGFE





































































































































Search results

Summary of Contents for RGFE

Reviews:

Related manuals for RGFE

Brands by name

Popular brands

Rheem RGFE, Installation Instructions Manual

Search results

Summary of Contents for RGFE

Reviews:

Related manuals for RGFE

Brands by name

Popular brands