Rheem RGFE Installation Instructions Manual Download Page 20

Page: 20 / 132

COMBUSTION AIR

ALWAYS PROVIDE THIS FUR-

NACE AND ANY OTHER FUEL

BURNING APPLIANCE WITH

ENOUGH FRESH AIR FOR

PROPER COMBUSTION AND

VENTILATION OF THE FLUE

GASES. MOST BUILDING

CODES REQUIRE THAT OUT-

SIDE AIR BE SUPPLIED INTO

THE FURNACE AREA. FAIL-

URE TO DO SO CAN CAUSE

DEATH FROM CARBON

MONOXIDE POISONING.

Provide adequate facilities for com-

bustion and ventilation air in accor-

dance with section 5.3, Air for

Combustion and Ventilation of the

National Fuel Gas Code, ANSI

Z223.1 - latest edition; CAN/CGA

B149.1 and .2, or applicable provi-

sions of the local building codes.

These combustion and ventilation

facilities must not be obstructed.

IMPORTANT:

Air for combustion and

ventilation must not come from a

corrosive atmosphere. Any furnace

failure due to corrosive elements in

the atmosphere is excluded from

warranty coverage.

The following types of installation (but

not limited to the following) REQUIRE

OUTDOOR AIR for combustion, due

to chemical exposures:

• Commercial buildings
• Buildings with indoor pools
• Furnaces installed in laundry

rooms

• Furnaces in hobby or craft rooms
• Furnaces installed near chemical

storage areas.

Exposure to the following substances

in the combustion air supply (but not

limited to the following) also

REQUIRE OUTDOOR AIR for com-

bustion:

• Permanent wave solutions
• Chlorinated waxes and cleaners
• Chlorine-based swimming pool

chemicals

• Water softening chemica

• De-icing salts or chemicals
• Carbon Tetrachloride
• Halogen type refrigerants
• Cleaning solvents (such as per-

chloroethylene)

• Printing inks, paint removers,

varnishes, etc.

• Hydrochloric acid
• Cements and glues
• Anti-static fabric softeners for

clothes dryers

• Masonry acid washing materials

Combustion air must be free of acid

forming chemicals such as sulphur,

fluorine, and chlorine. These ele-

ments are found in aerosol sprays,

detergents, bleaches, cleaning sol-

vents, air fresheners, paint and var-

nish removers, refrigerants and many

other commercial and household

products. Vapors from these products

when burned in a gas flame form acid

compounds. The acid compounds

increase the dew point temperature

of the flue products and produce

highly corrosive condensate.

TABLE 1

UNCONFINED SPACE DIMENSIONS

ALL FURNACE INSTALLATIONS

MUST COMPLY WITH THE

NATIONAL FUEL GAS CODE AND

LOCAL CODES TO PROVIDE ADE-

QUATE COMBUSTION AND VENTI-

LATION AIR FOR THE FURNACE.

FAILURE TO DO SO CAN RESULT

IN EXPLOSION, FIRE, PROPERTY

DAMAGE, CARBON MONOXIDE

POISONING, PERSONAL INJURY

OR DEATH.

Combustion air requirements are

determined by whether the furnace

is in an open (unconfined) area or in

a confined space such as a closet or

small room.

FURNACE LOCATED IN AN

UNCONFINED SPACE
Using indoor air for combustion.

An unconfined space must have at

least 50 cubic feet for each 1,000

BTUH of the

total input for all

appliances

in the space. Here are a

few examples of the room sizes

required for different inputs. The

sizes are based on 8 foot ceilings.

See Table 1.

If the open space containing the fur-

nace is in a building constructed to

severely limit outside air infiltration

(contemporary energy efficient con-

struction methods), outside air may

still be required for the furnace to

operate and vent properly. Outside

air openings should be sized the

same as for a confined space.

BTUH Minimum Sq. Feet Typical Room Size

Input With 8 foot Ceiling

60,000

375

15' x 25' OR 19' x 20'

75,000

469

15' x 32' OR 20' x 24'

90,000

563

20' x 28' OR 24' x 24'

105,000

657

20' x 33' OR 26' x 25'

120,000

750

25' x 30' OR 24' x 32'

WARNING

NON-DIRECT VENT PIPE INSTALLATION

(FOR VERTICAL TERMINATIONS ONLY)

Summary of Contents for RGFE





































































































































Search results

Summary of Contents for RGFE

Reviews:

Related manuals for RGFE

Brands by name

Popular brands

Rheem RGFE, Installation Instructions Manual

Search results

Summary of Contents for RGFE

Reviews:

Related manuals for RGFE

Brands by name

Popular brands