manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 99

99

23. Handling

•  Never connect the mains plug to a mains socket immediately after the device has been taken from a cold to a warm environment. The result

-

ing condensation may destroy the device. Allow the device to reach room temperature before connecting it. Wait until the condensation has 

evaporated.

•  Never pull the mains plug from the mains socket by the cable. Only pull it from the mains socket by the intended grip areas.
•  Disconnect the 3D printer from the mains voltage if you are not going to use it for an extended period of time.
•  Disconnect the mains plug from the mains socket during thunderstorms for reasons of safety.
•  The heating plate and the extruders may heat up strongly in operation. Do not touch these parts during or just after operation.  Let these parts 

cool off first. Attention! Danger of burns!

24. Disposal

  The product does not belong in the household waste!

 

Dispose of the product according to the relevant statutory regulations at the end of its service life.

25. Technical data

Operating voltage ................................ 230 V/AC, 50 Hz
Power intake 3D printer ....................... max. 760 W
Connection output socket .................... max. 800 W
Total power intake ................................ max. 1560 W
Fuse ..................................................... T6.3AL/250 V (5 x 20 mm, slow-acting trigger)
Production process .............................. FFF (Fused Filament Fabrication) / FDM (Fused Deposition Modelling)
Printing space (W x D x H) ..................

Single extruder approx. 200 x 290 x 185 mm (X, Y, Z)

.............................................................

Dual extruder approx. 170 x 290 x 185 mm (X, Y, Z)

Printing layer thickness ........................ 0.05 - 0.3 mm
Nozzle diameter ................................... 0.4 mm

Suitable filament material

 .................... ABS, PLA, PVA, EcoPLA™, PET, Taulman, Layrick, Bendlay, Laywood-D3, HIPS and smartABS

Filament diameter ................................ Standard, max. 1.75 mm
Power of the heating plate ................... 560 W
Extruder temperature ...........................

120 – 270 °C

Heating plate temperature ...................

55 – 160 °C

Interfaces ............................................. USB 2.0 and SD/SDHC card reader
Dimensions (W x D x H) ...................... 390 x 420 x 665 mm
Weight ................................................. 19.7 kg

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands