Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 7

Page: 7 / 110

5. Important advice and notes - Please read!

ATTENTION Mains voltage - the connection, installation and wiring of the electrical components must only be performed

by an electrician who is familiar with the applicable safety provisions. Before commissioning, inspection according to the

applicable safety provisions must be performed by an electrician. This also applies to repair work.

Observe all safe

ty and assembly notes in these operating instructions and in the assembly instructions!

Attention! Important note on shipping of the printer!

Please keep the original outer packaging and the inlay well! Only this permits safe transport, e.g. for guarantee/warranty!

Please observe the separate packaging instruction as well.

We assume no liability in case of transport damage to devices that were not sent out in their original packaging or that were

packed improperly in it!

Attention! Important note on the firmware and software of the printer!

This version of the instruction is valid as of master firmware version RF.01.42 or higher and

Repetier-Host software version

2.0.5 or higher. If your printer has an older firmware or your computer an older software installed, first install the latest ver

sions.

Install the next master firmware version as soon as it is available.

On this, observe chapter "

12. Software and firmware installation

" or chapter "20. Firmware update with the Arduino

IDE".

Update the enclosed memory card as well. The corresponding download can be found on the respective product page of

our website or in the download area.

Important Note for maintenance and repair

If there are any further errors in your printer or any expanded maintenance (e.g. exchange of the entire extruder or parts of

it), we recommend that you have a look at the assembly instructions of the RF2000 v2 construction kit. This can be very

helpful if all construction steps are described most precisely.

You can find the instructions on the product page of the construction kit (Conrad order no. 1563100) or in the download

area on our website (see item "Current Operating Instructions" in chapter "3. Intended use").

Important Note for using the spatula

The enclosed spatula is meant for removal of the objects that are still stuck to the printing plate and that are difficult to remove without help.

Proceed with the utmost care when using the spatula!

The spatula should only be used if there is any printing film or adhesive tape on the printing plate. Also use the spatula only

at a very flat angle.

Non-observation of the notes or wrong handling may damage the surface of the printing plate and thus influence the print

quality! This may also cause loss of the warranty/guarantee!

Summary of Contents for RF2000 v2 BSS















































































































Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands