manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 65

65

(1)  Object filling (0-100%)

 We recommend object filling of 10% to 40%.

(2)  Filling pattern of the object and the first and last layer

(1)  Loops are circles, that are drawn around the object when printing starts, stabilise the filament flow before the actual object is printed. Here, 

number, distance from the object, height and minimum length are specified.

 For 2-coloured printing objects, a wall will be drawn around the object that is used to wipe off the extruders. The bottom-most layer 

is broader than the wall here (see red arrow in the small picture). The length of this layer is specified in the setting "

Minimum extru-

sion length

". A value of approx. 25 mm is enough for a printed object with a diameter of up to approx. 50 mm. If you want to print 

larger 2-coloured objects, increase the value accordingly. Proceed with caution for this, since the layer may otherwise reach to below 

the printing object.

(2) "

Brim

" is a thin edge that is placed right around the object to increase the footprint and thus adhesion to the printing plate. Here, the width 

of the brim is specified.

2

1

2

1

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands