manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 3

3

Page

15.  Inserting, removing and changing the filament

 ............................................................................................................................................42

 

a)  Inserting the filament - Mechanical part

 .................................................................................................................................................42

 

b)  Inserting the filament via the printer menu

 .............................................................................................................................................43

 

c)  Removing and changing the filament

 ....................................................................................................................................................45

16.  First print of an example object from the SD card ........................................................................................................................................46
17.  General notes on 3D printing .......................................................................................................................................................................48
18.  Software "Repetier-Host" .............................................................................................................................................................................49
 

a)  Connection of the connected printer ......................................................................................................................................................49

 

b)  Manual operation via the software .........................................................................................................................................................51

 

c)  Placement of a printing object in the software .......................................................................................................................................52

 

d)  Preparation for print ...............................................................................................................................................................................56

  e) Print .......................................................................................................................................................................................................60
 

f)  More detailed description of the slicer functions ....................................................................................................................................63

 

g)  Setting up another Slic3r version ...........................................................................................................................................................73

19.  Extended calibration ....................................................................................................................................................................................77
 

a)  Determining the highest position of the printing plate ............................................................................................................................77

 

b)  Fine adjustment of the filament infeed

 ...................................................................................................................................................81

 

c)  Fine adjustment of the two extruders .....................................................................................................................................................84

 

d)  Correction of the printing plate temperature ..........................................................................................................................................86 

20.  Firmware update with the Arduino

TM

 IDE......................................................................................................................................................87

21. Maintenance ................................................................................................................................................................................................91
 

a)  General information ...............................................................................................................................................................................91

  b) Cleaning .................................................................................................................................................................................................91
 

c)  Fuse replacement ..................................................................................................................................................................................92

 

d)  Checking the belt tension ......................................................................................................................................................................93

 

e)  Nozzle change .......................................................................................................................................................................................95

22. Troubleshooting ...........................................................................................................................................................................................96
23. Handling .......................................................................................................................................................................................................99
24. Disposal .......................................................................................................................................................................................................99
25.  Technical data ..............................................................................................................................................................................................99
26. Annex .........................................................................................................................................................................................................100
 

a)  Wiring plan ...........................................................................................................................................................................................100

 

b)  Setting up the printer settings ..............................................................................................................................................................102

 

c)  Status and error messages ..................................................................................................................................................................105

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands