manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 27

27

Extruder

Temp. Bed: 0 °C Manually adjusting the heat bed temperature
Temp. 0      : 0 °C

Manually setting the extruder temperature extruder 0 (e.g. for filament change)

Temp. 1      : 0 °C

Manually setting the extruder temperature extruder 1 (e.g. for filament change)

Extruder 0 Off

Switches off heater of the 1st extruder

Extruder 1 Off

Switches off heater of the 2nd extruder

Active Extruder

Specifies which extruder is active (push OK to switch)

Position extruder Manually operate extruder infeed/1 mm per click/works only if the extruder is heated up
Load Filament

Inserting the filament/extruder is heated up automatically, then the filament is pulled in

Unload Filament

Removing the filament/extruder is heated up automatically, then the filament is moved out

Set E Origin

Set the new zero point

Fan Speed

Fan Speed: 0%

Displays the current fan speed (0% - 100%)

Turn Fan off

Switches the fan off; is only displayed if the fan has been switched on manually

Fan to 25%

Sets the fan speed to 25%

Fan to 50%

Sets the fan speed to 50%

Fan to 75%

Sets the fan speed to 75%

Fan to 100%

Sets the fan speed to 100%

SD Card

Print File

Start print from SD card

Delete File

Delete file from SD card (then the file to be deleted is selected)

Configuration

General

Baud Rate: 115200

Setting of the transfer speed from the computer

Stepper off

Time setting until the motors are switched off in standby

All off

Time setting until the motors and heaters are switched off in standby

Beeper: On/Off

Switches the button sound on or off

Mode: Printer/Miller

Switches between the printer and mill modes

Z Scale: Z Min/Surface

Specifies point Z = 0 for the display Z (5) in the main menu:
Z Min: specifies Z-Min, i.e. the Z home position as zero position
Surface: specifies the surface of the heat bed as zero position

Hotend: V3

Switches between the versions of extruders (the RF2000 v2 only supports the hotend V3)

Extruder Offset X

Specifies the distance between the two extruders in the X-direction
(Standard = 33.594; indication in mm)

Extruder Offset Y

Specifies the distance between the two extruders in the Y-direction
(Standard = 0.000; indication in mm)

Acceleration

Print X: 1000

Sets the max. printing acceleration of the X-axis

Print Y: 1000

Sets the max. printing acceleration of the Y-axis

Print Z: 100

Sets the max. printing acceleration of the Z-axis

Move X: 1000

Sets the max. travelling speed of the X-axis

Move Y: 1000

Sets the max. travelling speed of the Y-axis

Move Z: 100

Sets the max. travelling speed of the Z-axis

X/Y-Jerk: 10.0

Max. acceleration of the X and Y axis at small steps

Z-Jerk : 0.1

Max. acceleration of the Z axis at small steps

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands