manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 9

9

 

c) Operation

•  Push the emergency off switch at once if there is any electrical or mechanical problem! The printer will be powered down by this. 

Only reset the emergency off switch when the problem has been removed.

•  Never reach into the 3D printer in operation. The mechanically moved parts within the printer pose a high risk of injury!
•  The print head and the printing plate grow very hot in operation. Never touch these parts during or just after operation. Let them 

cool down sufficiently first (approx. 60 minutes).

•  Disconnect the device from the mains before maintenance work or modifications (unplug the mains plug!) and let it cool down.
•  In operation, there will be noise and, depending on the filament material used, smells. Observe this when selecting the site of setup 

and the filament material. Ensure sufficient ventilation or install an extraction system. Do not inhale arising vapours. When using 

any other than the recommended filament material, poisonous vapours or gases may develop.

•  Do not touch the mains cable if it is damaged. First power down the respective mains socket on all poles (e.g. switch off circuit 

breaker and FI switch) and then pull the mains cable from the socket. Never operate the product with a damaged mains line.

•  Never touch the mains line or the mains plug with wet or damp hands. There is a risk of potentially fatal electric shock!
•  Never operate the device unattended.
•  Only operate the device in moderate climates, never in tropical climates.

 

d) Socket

•  The socket on the rear of the 3D printer serves to connect suitable devices. The socket is controlled separately by the 3D printer 

as required. 

  Never connect any other devices here that are not intended for operation in connection with the 3D printer.

•  Do not overload the socket. The maximum permitted output power is indicated on the socket (also see chapter "25. Technical 

data").

•  The mains cable must not be squeezed or damaged by sharp edges. Do not put any objects onto the mains cable and do not step 

on it. Place the mains cable so that no one can trip over it and that the mains lug is easily accessible. 

  Also place the mains cable so that there can be no damage when operating the 3D printer.

•  Always pull a mains plug from the socket by the provided grip; never pull out a mains plug from the socket by the cable! 
•  Do not connect in series! Do not connect any socket strip to the socket of the 3D printer.
•  Do not operate covered! 
•  Voltage-free only when the plug is pulled! The socket is controlled separately by the 3D printer. The mains voltage therefore may 

increase inadvertently. 

  For example, if you want to operate a device via the 3D printer socket, first pull the mains plug of the device from the 3D printer 

socket before performing any work on it.

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands