manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 17

17

c) Inspection of the fan sheet and the actuation for the Z-limit switch

The two extruders should be in the home position. This means that they both need to touch the extruder holder on top.

The fan sheet height must be set so that the two upper screws of the two rear fans do not tough the X-plate (left figure). At the same time, the 

fan sheet must be above the two tips of the extruder nozzles (right figure). Of course, it should also be as straight as possible in reference 

to the extruder nozzles.

Additional, you need to observe that the fan sheet must not touch the 

attachment screws of the temperature sensors of the two extruders.

Also make sure to check the actuation for the Z-limit switch.

This must be aligned so that the square is aligned in parallel with the 

light barrier and can move into it cleanly. Also check that the hexagon 

threaded bolt and the counter nut of the actuation are tightened and 

that the entire unit or the actuation cannot be adjusted.

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands