manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 20

20

The software Repetier-Host performs the following tasks:

•  Placement of the 3D-object to be printed on the printing plate.
•  Slicing of the object to be printed into thin layers that the 3D printer can print out layer for layer. The result of this process is a G-code file.
•  Review of the G-code files for error and printability.
•  Sending the G-code files to the printer or saving on an SD card for standalone print.
•  Monitoring the 3D printer in operation.
•  Setting and storage of printer and filament-specific data.

c) Installation of the Repetier-Host software

•  Install the file "

setupRepetierHostRenkforce_x_x_x.exe

" from the directory "

Repetier-Host

" from the download package or the SD card 

(x_x_x designates the software version here).

 

Installation of the custom version of the Repetier-Host requires administrator rights, since the necessary configuration files and 

printer settings will not be installed otherwise. If the corresponding message appears in Windows

®

, confirm it with Yes in any case. 

The installation will otherwise be interrupted.

 

If setup asks if you want to install the serial drivers ("Install serial driver"), do this in any case for the first installation, since the printer 

will not be recognised otherwise.

•  Alternatively, the installation file for the basic version of the software can also be downloaded from 

www.repetier.com

. There, MacOS X and 

LINUX versions of this software are offered as well.

 

Prerequisites for installing under Windows

®

:

 

Microsoft .Net Framework 4 must be installed on the computer. This software can be downloaded free of charge from  

www.microsoft.com or installed subsequently in the operating system via the Windows

®

 features.

 

The further system requirements for installation of Repetier-Host (also for other operating systems) are found on www.repetier.com.

 

Updates for Repetier-Host are regularly published under www.repetier.com.

d) Updating of the firmware

 

Before you continue, first check if a new version of the firmware is available.

 

The updated version of the firmware always is contained in the download package "RF2000v2_SD_Vx.x.zip". The firmware 

is also available for download on Github.

 

On this and the update process, always observe chapter "20. Firmware update with the Arduino

TM

 IDE".

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands