Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 107

Page: 107 / 110

107

Error:

Park Heat Bed

Operation denied

Is displayed when someone tries to start park head bed while printing/milling is active.

Can be caused by:

- M3080

- the menu item "Park Heat Bed"

This function is currently switched off by default.

Error:

Pause

Home unknown

Is displayed when printing/milling cannot be paused because the home position is not known.

Can be caused by:

- M25

- Emergency Pause

- the menu item "Pause Print"

- the menu item "Pause Mill"

- the hardware button "Pause"

This error theoretically should never happen.

Error:

Pause

Operation denied

Is displayed when printing/milling cannot be paused because printing/milling is not currently active.

Can be caused by:

- M25

- the hardware button "Pause"

Error:

Z Compensation

Invalid Matrix

Is displayed when the Z-compensation cannot be activated (or the Z-compensation matrix cannot be displayed)

because the Z-compensation matrix is not present or invalid.

Can be caused by:

- M3001

- M3013

- M3141

- M3153

Error:

Z Compensation

Home unknown

Is displayed when Z-compensation cannot be activated because the home position is not known.

Can be caused by:

- M3001

- M3141

Error:

Z Compensation

Operation denied

Is displayed when the Z-compensation matrix cannot be changed or deleted because:

- the Z-compensation is currently active

Error:

Find Z Origin

Operation denied

Is displayed when the RF is in "Printer" mode.

Error:

Home

Operation denied

Is displayed when the "Home" position cannot be targeted because:

- printing/milling is underway

- a heat bed scan is underway

- a work piece scan is underway

- search for the Z-origin is underway

- the DMS-test is underway

Error:

Change Mode

Operation denied

Is displayed when the operating mode cannot be changed because:

- printing/milling is underway

- a heat bed scan is underway

- a work piece scan is underway

- search for the Z-origin is underway

- the DMS-test is underway

Can be caused by:

- the menu item "Mode"

Error:

Change Z Type

Operation denied

Is displayed when the Z-type cannot be changed because printing/milling is currently underway.

Can be caused by:

- the menu item "Z Type"

Error:

Change Hotend

Operation denied

Is displayed when the hotend type cannot be changed because printing is currently underway.

Can be caused by:

- the menu item "Hotend"

Error:

Change Miller

Operation denied

Is displayed when the mill type cannot be changed because milling is currently underway.

Can be caused by:

- the menu item "Miller"

Summary of Contents for RF2000 v2 BSS















































































































Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands