manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 41

41

Push 

OK

, to select "

Scan

" and start the heat bed scan this way. Push 

the direction button "

left

" 3 x to return to the main menu.

The status display of the main menu shows "

Heat Bed Scan

". The 

geometry of the printing plate is now measured automatically. This 

process will take a while.

Aligning the right extruder

After the measurement has been performed, the printing plate and 

the extruder unit return to their home positions and then immediately 

move to the middle of the printing plate.

The heating of the extruders and the printing plate is switched off 

automatically.

The display shows "

Align Extruders

".

This means that the second extruder must be aligned now. 
Heat up the printing plate to 100 °C again and the two extruders to 

120 °C. Proceed as described in this chapter, in item "Heating up the 

printing plate and the extruders". 
Again, wait for at least 10 minutes when the set temperatures are 

reached.

The extruder 0 should now be supported nearly entirely on the print-

ing plate.

To be certain, first release the holding screw of the left extruder (ex

-

truder 0), so that it is actually supported on the printing plate.
Then release the screw of the right extruder (extruder 1) and lower it 

carefully onto the printing plate. 
Now tighten the two screws again in sequence. Best hold the extrud-

er at the very top of the inlet. This prevents them from twisting and 

hitting the fan sheet. Both extruders must be applied to the printing 

plate with the same force.
Press the button "

Play

" (6) to terminate Heat Bed Scan.

Attention! Never touch the hot extruder or the printing plate dur-

ing the settings! There is a danger of burns!

When the information "

Scan completed

" is displayed as shown in 

the figure, the scan has been completed successfully and the values 

have been saved.

Confirm the message with 

OK

.

The printer switches back to the main display.

You can use the printer now. Best continue by inserting the filament. 

If the display shows "

Scan aborted

", this means that measurement 

has been aborted.

In this case, observe chapter "22. Troubleshooting".

In this version of the head bed scan ("

Scan

"), you need to manually set the Z-offset (distance between nozzle/printing plate when printing the 

first layer) after the scan. For the settings for the Z-offset, see the menu "

Configuration

" - "

Z Calibration

" - "

Z Offset

". Alternatively, the Z-offset 

can also be controlled via the G-code.

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands