Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 108

Page: 108 / 110

108

Error:

Delete File

Operation denied

Is displayed when a file cannot be deleted from the SD card because printing/milling is currently underway.

Can be caused by:

- M30

- the menu item "Delete File"

Error:

X-Axis

Home unknown

Is displayed when the X-axis cannot be moved because the home position is not known.

Can be caused by:

- the menu item "Position X"

Error:

X-Axis

Operation denied

Is displayed when the X-axis cannot be moved because printing/milling is currently underway.

Can be caused by:

- the menu item "Position X"

Error:

Y-Axis

Home unknown

Is displayed when the Y-axis cannot be moved because the home position is not known.

Can be caused by:

- the menu item "Position Y"

Error:

Y-Axis

Operation denied

Is displayed when the Y-axis cannot be moved because printing/milling is currently underway.

Can be caused by:

- the menu item "Position Y"

Error:

Z-Axis

Home unknown

Is displayed when the Z-axis cannot be moved because the home position is not known.

Can be caused by:

- the menu item "Position Z"

- the hardware button "up"

- the hardware button "down"

Error:

Extruder

Operation denied

Is displayed when the extruder cannot be moved because it is too cold.

Can be caused by:

- the hardware button "Extract"

- the hardware button "Retract"

- the menu item "Load Filament"

- the menu item "Unload Filament"

- the menu item "Position Extruder"

Error:

Align Extruders

Operation denied

Is displayed when the alignment of the two extruders cannot be started because:

- Printing is currently being performed

- Only one extruder is installed

Error:

Align Extruders

Temperature wrong

Is displayed when the alignment of the two extruders cannot be started because:

- The temperature difference between extruder 1 and 2 is too high

Error:

Determine PID

Temperature wrong

Is displayed when it is found during automatic determination of the PID values that the actual temperature is

getting too high.

Can be caused by:

- M303

Error:

Determine PID

Timeout

Is displayed when automatic determination of the PID values cannot be completed within 20 minutes.

Can be caused by:

- M303

Error:

Temperature Manager

Sensor Error

Is displayed when a temperature sensor error is found (= the sensor returns a temperature < -10 or > +300 °C).

The firmware must be restarted before the temperature sensors will be evaluated again.

Error:

Emergency Z Block

Is displayed when all other movements in Z-direction are blocked due to too-high DMS values.

The firmware must be restarted before movement in the Z-direction is possible again.

Warning:

Emergency Pause

Is displayed when the current print/milling process has been paused due to too-high DMS values.

To continue printing/milling, push the "Continue" button.

Summary of Contents for RF2000 v2 BSS















































































































Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands