Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 105

Page: 105 / 110

105

c) Status and error messages

Some of the messages are displayed for a certain time and will then disappear again on their own. Other messages, such as those

starting with "Error:", are displayed until the user confirms them. Briefly push the button "

" (2).

Status messages

(Are displayed on the printer display)

Printer ready.

Is shown when the RF is ready for printing.

Miller ready.

Is shown when the RF is ready for milling.

Heating Extruder

Is displayed when an extruder heater has been activated because M109 has been received.

Heating Bed

Is displayed when a bed heater has been activated because M190 has been received.

Home X

Is displayed when the RF is homing the X-axis.

Home Y

Is displayed when the RF is homing the Y-axis.

Home Z

Is displayed when the RF is homing the Z-axis.

Killed

Is displayed when the RF was switched off the motors and radiators because it:

- has not performed any commands for a while

This "while" can be set via M85 or the "All off" menu.

- the operating mode (printing/milling) has switched

Stepper disabled

Is displayed when the RF has switched off the motors because it:

- has not performed any commands for a while

This "while" can be set via M85 or the "All off" menu.

- the operating mode (printing/milling) has switched

Heat Bed Scan

Is displayed while the heat bed scan is active.

Align Extruders

Is displayed at the end of the heat bed scan when the user must align the two extruders.

Is displayed when "Align Extruders" has been selected in the menu.

Align aborted

Is displayed when alignment of both extruders was cancelled.

Align completed

Is displayed when alignment of both extruders was completed.

Work Part Scan

Is displayed while the work piece scan is active.

Scan completed

Is displayed when the heat bed scan has been completed successfully.

Is displayed when the work piece scan has been completed successfully.

For more information on the errors that occurred, see the log file of the Repetier-Host.

Scan aborted

Is displayed when the heat bed scan has been cancelled.

Is displayed when the work piece scan has been cancelled.

For more information on the errors that occurred, see the log file of the Repetier-Host.

Preheat PLA

Is displayed when the extruder and printing plate are heated to PLA temperatures because the menu item "Pre-

heat PLA" has been chosen.

Preheat ABS

Is displayed when the extruder and printing plate are heated to ABS temperatures because the menu item "Pre-

heat ABS" has been chosen.

Cooldown

Is displayed when the extruder and printing plate are switched off because the menu item "Cooldown" has been

chosen.

Printing…

Is displayed when printing is active.

Milling…

Is displayed when milling is active.

Paused

Is displayed when the current print/milling process has been paused.

Unload Filament

Is displayed when the filament is output because the menu item "Unload Filament" has been chosen.

Load Filament

Is displayed when the filament is pulled in because the menu item "Load Filament" has been chosen.

Find Z Origin

Is displayed during the search for the Z-origin.

Search completed

Is displayed when the search for the Z-origin has been successfully completed.

Search aborted

Is displayed when the search for the Z-origin has been cancelled.

For more information on the errors that occurred, see the log file of the Repetier-Host.

Test SG

Is displayed while the DMS test is active.

Test completed

Is displayed when the DMS test has been completed successfully.

Summary of Contents for RF2000 v2 BSS















































































































Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands