manualshive.com logo in svg

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Share
Download
Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 106

106

Test aborted

Is displayed when the DMS test has been cancelled.

For more information on the errors that occurred, see the log file of the Repetier-Host.

SD Card removed

Is displayed when the RF recognises that the SD card has been removed.

SD Card inserted

Is displayed when the RF recognises that the SD card has been inserted.

SD Read Error

Is displayed when the RF recognises that a reading error has occurred.

SD Error fixed

Is shown when the RF has removed the reading error.

No SD Card

Is displayed when the RF wants to delete a file from the SD card but there is no SD card.

Uploading…

Is displayed when a file is transferred to the SD card.

Heating up…

Is displayed when the firmware is waiting after starting the heat bed scan until the extruder and/or the heat bed 

has heated up.

Cooling down…

Is displayed when the firmware is waiting after starting the heat bed scan until the extruder and/or the heat bed 

has cooled off.

Outputting…

Is displayed when Output Object is being executed.

Pausing…

Is displayed when moving to the Pause-Position.

Continuing…

Is displayed when moving to the Continue-Position.

Driving free Z

Is displayed when Z-Max

- is cleared in the scope of Z-homing

- is cleared after the end of printing/milling

PID determined

Is displayed when automatic determination of the PID-values has been successfully completed.

SERVICE

Is displayed when the firmware finds at activation that the service interval has been reached (or exceeded). This 

function is currently switched off by default.

Error messages

(Are either displayed in the printer display or in the log file of the Repetier-Host software) 

Error:

Set Origin

Home unknown

Is displayed when the origin cannot be set because the home position is not known.

Can be caused by:

- G92

- M3115

- the menu item "Set XY Origin"

Error:

Heat Bed Scan

Operation denied

Is displayed when someone tries to start the heat bed scan while printing is active.

Can be caused by:

- M3010

- the menu item "Scan Heat Bed"

Error:

Heat Bed Scan

Saving failed

Is displayed when the determined matrix could not be saved after the heat bed scan.

This error theoretically should never happen.

Error:

Work Part Scan

Operation denied

Is displayed when someone tries to start the work piece scan while milling is active.

Can be caused by:

- M3150

- the menu item "Scan Work Part"

Error:

Work Part Scan

Saving failed

Is displayed when the determined matrix could not be saved after the work piece scan.

This error theoretically should never happen.

Error:

Output Object

Operation denied

Is displayed when someone tries to start output object while printing/milling is active.

Can be caused by:

- M3079

- the menu item "Output Object"

Error:

Output Object

Home unknown

Is displayed when the output object is not possible because the home position is not known.

Can be caused by:

- M3079

- the menu item "Output Object"

- when printing/milling from the SD card has been completed

Summary of Contents for RF2000 v2 BSS















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands