Renkforce RF2000 v2 BSS Operating Instructions Manual Download Page 19

Page: 19 / 110

12. Software and firmware installation

a) Download and unpacking of the software/firmware package

The software, firmware, tools and printing examples needed for the printer are available online as a download package.

These are regularly updated. Therefore, check occasionally whether a new version may be available.

The download package is at the same time the content of the SD card. This means that if a new version is available online

here, you should update your SD card at the same time.

• Open the web browser and navigate either to the product page of the printer in our shop

www.conrad.com or to our download page (see

chapter "3. Intended use" - Current operating instructions).

• Download the package "

RF2000v2_SD_Vx.x.zip

" here (Vx.x designates the package version).

• Unpack the downloaded ZIP file on your hard disc. Note that the archive has a very deep path due to the firmware contained. Therefore, we

recommend directly unpacking the package into a folder on, e.g., C:\ or D:\.

• Update your SD card when you have unpacked the package. Also check the firmware version of your printer and the version of your Repetier-

Host. If the download package contains a newer version, update it!

• Find a brief explanation on the folders contained below.

Arduino

This folder holds the matching Arduino

version in its current status to match the firmware of the

printer. The text file additionally contains the download link.

Firmware

Firmware version for the software Arduino

Manual

This contains a text file with information on the download of the instructions.

“

PLA-GCODE

”

Printing examples for PLA that are already sliced. These can be printed directly from the SD card.

Repetier-Host

The custom version of the software Repetier-Host.

STL

Print examples that are not sliced yet.

Version.txt

In this text file, the version number of the download package is noted.

b) General information on the Repetier-Host software

It is unfortunately not possible to explain the complete function of the enclosed software in the scope of this instruction. For this, we refer to the

integrated online help function and the information on www.repetier.com.

The basic operation and the path to the first printout are, however, described below to that you can get a result quickly and easily.

The enclosed SD card or the archive you have downloaded before holds a custom version of the software that contains the

printer settings and configuration files for the RF2000 v2 in the folder "Repetier-Host".

We urgently recommend to install the custom version of the software since then you do not need to configure the software

and the required drives are already installed as well.

The respective updated Custom version of the software always is contained in the download package "RF2000v2_SD_

Vx.x.zip".

This version of the instruction is valid as of the Repetier-Host software version 2.0.5 or higher.

Configuration of the software is explained below in the Annex to these instructions for the sake of completeness. However,

the software only needs to be configured if you install the basic version of the software from

www.repetier.com.

If you have already installed a previous basic version of the software, the old version can be uninstalled and the custom

version can be newly installed. The slicer settings of the previous version are not deleted and reappear in the custom ver-

sion.

Summary of Contents for RF2000 v2 BSS















































































































Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands

Renkforce RF2000 v2 BSS, Operating Instructions Manual

Search results

Summary of Contents for RF2000 v2 BSS

Reviews:

Brands by name

Popular brands