Printronix P6000L User'S Reference Manual Download Page 50

Page: 50 / 234

Configuration

3-6

Configuration Printout

The configuration printout lists all of the currently selected configuration parameter values. A

sample configuration printout is shown in Figure 3-1.

The following general procedure can be used to obtain a configuration printout. Refer to the

Control Panel Switch Function Diagram for an illustration of the switches required to select

and display the parameter menus and values.

Verify the POWER indicator is lit and the printer is off line.

Repeatedly press CONFIG MENU until DIAGNOSTICS is displayed.

Press CONFIG VALUE; select and display the CONFIGURATION PRINTOUT menu.

Press RUN/STOP TEST. The configuration printout will be produced.

Press RUN/STOP TEST again to return to OFFLINE READY.

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands