Printronix P6000L User'S Reference Manual Download Page 46

Page: 46 / 234

Configuration

3-2

Character Set

Application Compatibility

Paper Format

Host Interface

Load Parameters

Save Parameters

Diagnostics

From these menus, the related configuration parameter values can be displayed and selected.

Configuration Procedure

Most configuration options can be selected from the control panel. The few hardware selecĆ

table configuration options are described in the Hardware Jumper Configuration section. To

verify or modify the configuration from the control panel, the printer must be powered up, ofĆ

fline (OFFLINE READY), and the printer configuration unlocked to select parameters in the

configuration menus.

Basic configuration procedure requires alternately pressing the CONFIG MENU and CONĆ

FIG VALUE switches to arrive at the desired parameter. The use of these switches and an illusĆ

tration of the configuration menus are described in the Control Panel Switch Function

Diagram section of this chapter. Thoroughly review the diagram to understand the configuraĆ

tion menu hierarchy and the control panel switches necessary to access and display individual

menus and parameter values.

The following general procedure can be used to reconfigure the printer from the control panel

as necessary to meet application requirements. Detailed descriptions are provided following

the general procedure.

Simultaneously press RUN/STOP TEST and CONFIG MENU to unlock the printer conĆ

figuration.

Obtain a current configuration listing as described in the Configuration Printout section

of this chapter.

Determine the parameter values that must be changed to meet requirements. Refer to the

Control Panel Switch Function Diagram for an illustration of the parameter values and

the procedure required to select and display the values.

Select and display the required value(s).

Enter the value(s) by pressing the RUN/STOP TEST switch.

Save the value(s) as the current default (if desired) as described in the Set/Save/Load

Configuration Value section of this chapter.

Simultaneously press RUN/STOP TEST and CONFIG MENU again to lock the printer

configuration.

Place the printer online. The selected values are effective.

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands