Printronix P6000L User'S Reference Manual Download Page 201

Page: 201 / 234

10-11

Installation

Pedestal Model Installation

The following section on Pedestal Model Installation provides information pedestal assembly,

table top mounting, and shipping restraints removal for the P6000L Series printers.

Pedestal Assembly

To assemble the optional pedestal for pedestal model printers, perform the following instrucĆ

tions. A 5/16" nut driver and 5/32" hex wrench are required.

Verify the pedestal shipping kit contains the following items:

2 pedestal legs

12 machine screws

1 modesty panel

4 flat washers

As shown in Figure 10-10, position the back side of the modesty panel (A) against the

pedestal legs (B) facing the long end of the leg base. With the 5/16" nut driver, secure the

panel to the legs with 4 machine screws (C) on each side of the back of the panel.

Place the printer on a sturdy table with 2 of the printer's rubber feet (D) hanging over the

edge of the table as shown in Figure 10-11. Using the 5/32-inch hex wrench, remove the

2 exposed rubber feet. Rotate the printer to expose the remaining 2 rubber feet and reĆ

move them.

As shown in Figure 10-12, carefully place the printer on the pedestal facing the front.

Align the printer's rubber feet holes (E

)

with the pedestal mounting holes (F). Install two

screws with washers through the pedestal mounting holes on each side to secure the

printer to the pedestal.

If equipped with the optional paper stacker, refer to the Paper Stacker Information and

Assembly Instructions.

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands