Printronix P6000L User'S Reference Manual Download Page 199

Page: 199 / 234

10-9

Installation

Removing the Side Shock Mount Restraint Screws

- After removing the side panel and lowerĆ

ing the card cage, the remaining four shock mount restraint screws can be accessed and reĆ

moved. Perform the following instructions and refer to Figure 10-9.

Remove the left two restraint screws (A) located above the fan housing (B) with the 3/8"

nut driver.

NOTE: A universal joint nut driver may be required to access the screws.

Remove the right two restraint screws (C) located to the right of the fan housing (B) with

the 3/8" nut driver.

After removing the last restraint screw, return the card cage to the full upright position

and tighten the wing nut.

Replace the side panel. Make sure the mounting studs and side panel release screw are

properly seated.

Tighten the side panel release screw.

Reconnect the ground wire connectors.

Lower the printer cover.

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands