Printronix P6000L User'S Reference Manual Download Page 21

Page: 21 / 234

2-1

Operation

CHAPTER 2

OPERATION

Introduction

This chapter describes basic P6000L/P6200L Series controls and operating procedures. OperaĆ

tion information and cleaning practices are also provided in the Operator's Guide. Refer to the

Installation chapter for information on power and site requirements, and printer installation.

P6000L/P6200L Series printers function either online or offline. When online, the printer is

capable of receiving data and control commands from the host computer. The message display

indicates the printer is online and the current print mode. When offline, communication is susĆ

pended between the printer and the host computer and the message OFFLINE READY apĆ

pears on the display. Set the printer offline to perform the following tasks:

Select Configuration Values

Configure the Printer

Run the Self-Test

Set Top-of-Form

Perform a Hex Dump

Set Line Spacing

Load Paper and Ribbon

Advance Forms

Change Print Modes

Adjust Paper Tractors

Advance Paper

Cleaning/Routine Maintenance

P6000L/P6200L Series printers respond to two different command sets or protocol modes:

P-Series emulation mode

Serial Matrix emulation mode

The selected protocol determines which programming standard is used by the host computer to

communicate with the printer. Either protocol can be selected as required by the application.

The P-Series emulation mode generates characters and graphics by using

Printronix

standard

P-Series control code protocol. The Serial Matrix emulation mode allows printing of characĆ

ters and graphics utilizing control codes similar to many serial matrix printers used with perĆ

sonal computers. The command protocol is selected via the P6000L/P6200L Series application

menu in the control panel. Refer to the Programming chapter for detailed information on P-

Series and Serial Matrix protocols and control code definitions.

There are two basic modes of operation: character printing (alphanumeric text) and graphics.

Character printing is the default mode of operation; graphics, either Serial Matrix compatible

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands