Printronix P6000L User'S Reference Manual Download Page 170

Page: 170 / 234

Interfaces

7-12

Interface Jumper Platform

If a change is made from a parallel (Dataproducts or Centronics) to an RS-232 interface or

vice versa, the interface jumper platform must be removed, turned around, and reinstalled.

The jumper platform must be properly installed for a parallel or RS-232 interface.

The interface jumper platform is located on the C3 logic board at position 6A. Refer to the

Hardware Jumper Configuration section in the Configuration chapter for instructions on reĆ

moving the C3 logic board.

Figure 7-3 illustrates jumper platform orientation. Table 7-4 describes serial or parallel

jumper configuration.

C3 Logic Board

RS-232 Interface

Jumper Orientation

C3 Logic Board

Parallel Interface

Jumper Orientation

Figure 7-3. Interface Jumper Platform Orientation

Table 7-4. Interface Jumper Configuration

Jumpers at Location 6A on C3 Logic Board

Interface Type

RS-232

Parallel

W10

O = OUT

I = IN

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands