Printronix P6000L User'S Reference Manual Download Page 205

Page: 205 / 234

10-15

Installation

Shipping Restraint Removal

The printer shipping restraints must be removed prior to operation. The following tools are

required to remove the shipping restraints from a pedestal model:

3/32" inch hex wrench

3/8" nut driver

diagonal cutters

WARNING

Do not connect the ac power source before removing the shipping restraints. If the

power has been connected, disconnect it prior to performing the shipping restraint

removal procedures to prevent possible injury. In addition, the shipping restraints

must be installed whenever the printer or shuttle assembly is shipped or transĆ

ported to prevent damage.

The printer contains 2 platen restraint screws and a foam rubber pad inserted behind the tracĆ

tor sprockets. Each screw is tagged with a red WARNING label. After mounting the printer on

the pedestal or table top, perform the following procedure and refer to Figure 10-14 to reĆ

move the shipping restraints. A 3/8" nut driver and a 3/32" hex wrench are required.

Raise the printer cover.

Rotate the Vertical Position Knob (A) clockwise and pull the rubber pad down and out.

Cut and remove the tie wrap securing the Forms Thickness Adjustment Lever (B

)

on the

left side of the printer.

Notice the red WARNING label on the restraint screw (C) on the left side of the printer.

Using a 3/8" nut driver or wrench, remove the restraint screw from the left side.

Notice the red WARNING label on the right side restraint screw (D). Using a 3/32" hex

wrench, remove the restraint screw from the right side.

Cut and remove the nylon string binding the power cord at the rear of the printer.

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands