Printronix P6000L User'S Reference Manual Download Page 195

Page: 195 / 234

10-5

Installation

Figure 10-4 illustrates the general location of the shipping restraints on the floor cabinet

model printer. Platen restraints include two screws (A) and a tie wrap around the Forms ThickĆ

ness Adjustment Lever (B). Two front shock mount restraint screws (C) and four side shock

mount restraint screws secure the entire print assembly to the chassis. Each screw is tagged with

a red warning label. After the printer has been placed in position, refer to the following instrucĆ

tions to remove the shipping restraints.

WARNING

Do not connect the ac power source before removing the shipping restraints. If the

power has been connected, disconnect it prior to performing the shipping restraint

removal procedures to prevent possible injury. In addition, the shipping restraints

must be installed whenever the printer or shuttle assembly is shipped or transĆ

ported to prevent damage.

Figure 10-4. Shipping Restraint Locations - Floor Cabinet Model

Summary of Contents for P6000L











































































































































































































































Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands

Printronix P6000L, User'S Reference Manual

Search results

Summary of Contents for P6000L

Reviews:

Related manuals for P6000L

Brands by name

Popular brands