Polaris 2010 OUTLAW 450 MXR Page 70 Owner'S Manual Download | Manualshive

Page: 70 / 212

background image

66

Operation

Starting the Engine

The engine can be started when the transmission is in neutral, or while in gear if the clutch is

disengaged. If starting a warm engine, do not use the choke.
Fuel is injected into the intake passage each time the throttle lever is depressed. Do not

depress the throttle lever while starting the engine. Do not depress the throttle lever when the

engine is stopped.

NOTICE:

Operating the ATV immediately after starting could cause engine damage. Allow the engine

to warm up for several minutes before operating.

1. Shift the transmission to neutral.
2. Lock the parking brake. Turn the fuel valve on.
3. Sit on the vehicle. Disengage the clutch.
4. If the engine is cold, pull the choke knob out until it

stops. Do not use the choke if starting a warm

engine.

Choke Knob

«
...
68
69
70
71
72
...
»

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Reviews:

No comments

Related manuals for 2010 OUTLAW 450 MXR

Brand: Baja motorsports Pages: 15

Twister UM250IIR

Brand: Hammerhead Pages: 67

Brand: Yamaha Pages: 222

YXZ 1000 R SS 2023

Brand: Yamaha Pages: 216

Brand: ABI Attachments Pages: 28

Brand: HYOSUNG Pages: 133

Brand: gio Pages: 20

Brand: Costway Pages: 7

Brand: Polaris Pages: 109

Chem-Veyor 2614D

Brand: Walinga Pages: 28

Brand: Xingyun Pages: 92

Brand: HAPERT Pages: 45

Brand: Taylor-Dunn Pages: 260

Brand: Ski-Doo Pages: 28

Brand: Suzuki Pages: 33

Brand: Power Fist Pages: 8

Brand: Nucamp Pages: 57

Brand: Interstate Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands