Polaris 2010 OUTLAW 450 MXR Page 51 Owner'S Manual Download

Page: 51 / 212

Features and Controls

Hand Brake

The hand brake operates the front brakes. The hand

brake is located on the right handlebar.

These brakes

are hydraulically activated disc type brakes.

Squeeze

the brake lever toward the handlebar to engage the

front brakes.
Always test brake lever travel and master cylinder

fluid level before riding. When squeezed, the lever

should feel firm. Any sponginess would indicate a

possible fluid leak or low master cylinder fluid level,

which must be corrected before riding. Contact your

dealer for proper diagnosis and repairs.

WARNING!

Operating the ATV with a spongy brake lever can result in loss of braking, which could

cause an accident. Never operate the ATV with a spongy-feeling brake lever. Always contact your

dealer for service before operating the vehicle.

Hand Brake

(Front Brake)

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands