Polaris 2010 OUTLAW 450 MXR Page 79 Owner'S Manual Download | Manualshive

Page: 79 / 212

background image

75

Operation

Turning Around on a Hill

If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn

around:
1. Keep your body weight uphill.
2. Pull in the clutch lever and apply the front and rear brakes.
3. When completely stopped, shut off the engine. Leaving the transmission in gear, release

the clutch lever and lock the parking brake.

4. Dismount on the uphill side of the vehicle, or on the left side if the vehicle is pointing

straight uphill.

5. Staying uphill of the ATV, turn the handlebars full left.
6. Reach across the handlebar and apply the front brakes to unlock the parking brake.

«
...
77
78
79
80
81
...
»

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Reviews:

No comments

Related manuals for 2010 OUTLAW 450 MXR

Brand: Yutrax Pages: 10

Brand: Nakayama Pages: 14

Camoplast ATV T4S

Brand: CAMSO Pages: 16

5000-05-1774-MAN

Brand: CAMSO Pages: 17

Brand: Ivarssons i Mestjö Pages: 32

Brand: Tomberlin Pages: 151

Brand: NorthStar Pages: 24

Brand: Baumax Pages: 12

Brand: Humbaur Pages: 230

Brand: Polaris Pages: 1

Brand: Landoll Pages: 62

Brand: Taylor-Dunn Pages: 200

B0-T48-48 Taylor Truck T48

Brand: Taylor-Dunn Pages: 196

Brand: Hammerhead Pages: 70

Brand: Hammerhead Off-Road Pages: 75

500 MXU IRS 4X4 NAKED EFI

Brand: KYMCO Pages: 1

Brand: BOMBARDIER Pages: 44

Brand: Honda Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands