Polaris 2010 OUTLAW 450 MXR Page 72 Owner'S Manual Download

Page: 72 / 212

Operation

Driving Procedures

1. Wear a helmet and eye protection.
2. Sit upright with both feet on the footpegs and

both hands on the handlebars.

3. Start the engine and allow it to warm up.
4. Shift the transmission into gear. See page 52.
5. Check your surroundings and determine your

path of travel.

6. Release the parking brake.
7. Slowly depress the throttle with your right

thumb while slowly releasing the clutch lever to

begin driving.

8. Drive slowly. Practice maneuvering and using

the throttle, clutch and brakes on level surfaces.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands