Home
/
Polaris
/
2010 OUTLAW 450 MXR
/
Owner'S Manual

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual, Page: 90 / 212

Share

Page: 90 / 212

Polaris 2010 OUTLAW 450 MXR Owner'S Manual Download Page 90

86

Emission Control Systems

Exhaust Emission Control System

The emissions from the exhaust of this vehicle are controlled by engine design, including

factory-set fuel delivery and ignition. The engine and related components must be main-

tained at Polaris specifications to achieve optimal performance.
Engine idle speed is the only adjustment Polaris recommends that the operator perform. Any

other adjustments should be performed by an authorized Polaris dealer.
The emissions label is located on the front frame tube near the steering post.

Electromagnetic Interference

This spark ignition system complies with Canadian ICES-002.
This vehicle complies with the EMC requirements of European directives 97/24/EC and

2004/108/EC.

«
...
88
89
90
91
92
...
»

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Reviews:

No comments