Polaris 2010 OUTLAW 450 MXR Page 152 Owner'S Manual Download | Manualshive

Page: 152 / 212

background image

148

Maintenance

Chain Tension Adjustment

1. Loosen the two eccentric locking bolts. Refer to the illustration on the following page.
2. Insert a pin punch into the eccentric axle housing.
3. Roll the vehicle slightly to adjust chain slack to the proper dimension.
4. Tighten the eccentric locking bolts to 35 ft. lbs. (47.5 Nm).

«
...
150
151
152
153
154
...
»

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Reviews:

No comments

Related manuals for 2010 OUTLAW 450 MXR

Brand: KYMCO Pages: 1

Brand: FARMA Pages: 36

Polar Trailer 10537

Brand: Clam Pages: 7

Trailblazer E2020

Brand: Evinrude Pages: 14

Off-Roader 36EL

Brand: Texas Pages: 27

amphibious, off-road utility vehicle

Brand: Centaur Pages: 56

Brand: X-TREME Pages: 25

Sportsman 90 2011

Brand: Polaris Pages: 12

2015 RZR XP 1000 EPS

Brand: Polaris Pages: 150

Brand: Traxxas Pages: 26

Brand: Labrie Pages: 62

Brand: Qpod Pages: 12

Brand: Landa Pages: 14

Brand: HAPERT Pages: 45

Brand: Yamaha Pages: 431

GRIZZLY 550 2010

Brand: Yamaha Pages: 172

Brand: The Handy Pages: 8

Brand: The Handy Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands