Polaris 2010 OUTLAW 450 MXR Page 142 Owner'S Manual Download

Page: 142 / 212

138

Maintenance

Clutch System Bleeding

Always bleed the clutch system at the intervals out-

lined in the Periodic Maintenance Chart beginning on

page 87. Always bleed the clutch system any time the

clutch lever feels unresponsive.
Always use the recommended fluid when bleeding

the clutch system. See page 43.
1. Position the vehicle on a level surface. Turn the

handlebar until the master cylinder is in a hori-

zontal position.

2. Remove the two cover screws, the cover and the

rubber boot.

3. Fill a bleeder syringe (1) with the recommended

hydraulic clutch oil.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands