Polaris 2010 OUTLAW 450 MXR Page 36 Owner'S Manual Download

Page: 36 / 212

Safety

Safety Warnings

Operating on Frozen Bodies of Water

Operating on frozen bodies of water may result in

serious injury or death if the ATV and/or the

operator fall through the ice. Never operate the

ATV on a frozen body of water.

Operating a Damaged ATV

Operating a damaged ATV can result in an

accident. After any overturn or accident, have a

qualified service dealer inspect the entire

machine for possible damage, including (but not

limited to) brakes, throttle and steering systems.

Physical Skills

Safe operation of this rider-active vehicle

requires good judgement and physical skills.

Persons with cognitive or physical disabilities

who operate this vehicle have an increased risk

of overturn and loss of control.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands