Polaris 2010 OUTLAW 450 MXR Page 179 Owner'S Manual Download

Page: 179 / 212

175

Troubleshooting

Engine Turns Over, Fails to Start

Possible Cause

Solution

No spark to spark plug

Inspect, clean and/or replace spark plugs

See your Polaris dealer

Overuse of choke/flooded engine

Engage starter 2 times for 5 seconds each, then restart.

If engine fails to start, inspect, clean and/or replace

spark plugs.

Low battery voltage

Recharge battery to 12.8 VDC

Ignition system or other mechanical failure

See your Polaris dealer

Throttle ETC switch not opening

Adjust throttle freeplay

The plug connection of the CDI-unit, pulse generator

or ignition coil has oxidized

Clean the plug connection and treat with contact spray

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands