Polaris 2010 OUTLAW 450 MXR Page 50 Owner'S Manual Download

Page: 50 / 212

Features and Controls

Foot Brake

The foot brake operates the rear brakes. The

brake pedal is located in front of the right-hand

footpeg. If the rear wheels slide while using

the foot brake, reduce brake pedal pressure to

brake the wheels without skidding.
Check the brake fluid level frequently for the

foot brake system. The reservoir is located

under the seat. Maintain the fluid level

between the minimum and maximum marks.

WARNING!

Aggressively applying the foot brake when backing down a hill may cause rear tipover,

which could result in serious injury or death. Never back down a hill. Use caution when applying the

foot brake. Do not aggressively apply the foot brake when going forward. The rear wheels may skid

and slide sideways, causing loss of control.

Footpeg

Foot Brake

(Rear Brake)

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands