Polaris 2010 OUTLAW 450 MXR Page 130 Owner'S Manual Download

Page: 130 / 212

126

Maintenance

Vehicle Immersion

If the vehicle tips or overturns in water deeper than the footpeg level, or if the engine stops

during or after operating in water, restarting WILL result in serious engine damage. Trans-

port the vehicle to your dealer for service before restarting the engine. If this is not possible,

follow the vehicle immersion inspection and drying procedures outlined below. This proce-

dure will allow

short-term operation only

to drive the ATV to a trailer or towing vehicle.

Do not perform the following procedures if you don't feel completely capable, or if you sus-

pect that water has entered the fuel tank (likely if the water was deep or if the ATV over-

turned). Tow or trailer the ATV to your dealer for immediate service.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands