Polaris 2010 OUTLAW 450 MXR Page 190 Owner'S Manual Download

Page: 190 / 212

186

Declaration of Conformity

Polaris Industries Inc.,
2100 Hwy 55, Medina, MN 55340 U.S.A.
Telephone 763-542-0500

We, Polaris Industries Inc., declare that the vehicles listed below conform to the essential health and safety

requirements applicable to off-road all-terrain vehicles.

APPLICABLE EUROPEAN DIRECTIVES

TEST / EVALUATION METHODS

98/37/EC as amended (Machinery Directive)

EN 1050 hazard analysis

CD 77/311/EEC driver-perceived noise level

2004/108/EC as amended (EMC Directive)

CISPR 12:2001

CAN/CSA-C108.4-M92

EN 55012:2002

EN 61000-6-2:2001

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands