Polaris 2010 OUTLAW 450 MXR Page 10 Owner'S Manual Download

Page: 10 / 212

Introduction

Safety Words and Symbols

The following signal words and symbols appear throughout this manual and on your vehicle.

Your safety is involved when these words and symbols are used. Become familiar with their

meanings before reading the manual.

The safety alert symbol indicates a potential

personal injury hazard.

WARNING

A WARNING indicates a hazardous situation

which, if not avoided, may result in death or

serious injury.

CAUTION

A CAUTION indicates a hazardous situation

which, if not avoided, may result in minor or

moderate injury.

NOTICE

A NOTICE indicates a situation that may result in

property damage.

The Prohibition Safety Sign indicates

an action NOT to take in order to avoid

a hazard.

The Mandatory Action Sign indicates

an action that NEEDS to be taken to

avoid a hazard.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands