Polaris 2010 OUTLAW 450 MXR Page 119 Owner'S Manual Download

Page: 119 / 212

115

Maintenance

Carburetor Jetting

Carburetor re-jetting can be performed to compensate for altitude and/or temperature

changes. If the vehicle is to be operated at various altitudes and temperatures, certain adjust-

ments can be made to improve its operation and driveability. Above 6000 feet (1800 m) the

engine air/fuel mixture becomes overly rich. An engine loses approximately 3% of its power

for each 1000-foot (305 m) increase in elevation. Although this power cannot be regained,

changes to the carburetor and drive system can be made to allow more efficient operation.
Contact your dealer for altitude adjustments. Your dealer has the training and special tools

required to perform these modifications.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands