Polaris 2010 OUTLAW 450 MXR Page 132 Owner'S Manual Download

Page: 132 / 212

128

Maintenance

Vehicle Immersion

6. Press and hold the starter button for 10 second intervals for about one minute or until

water vapor is no longer ejecting from the spark plug hole.

7. Check the oil level. If the level is higher than the pre-ride inspection level, water has

entered the crankcase.

Do not start the engine.

Transport the vehicle to your dealer for

inspection and service. If the oil level is unchanged from the pre-ride inspection level,

replace the spark plug, start the engine and move the ATV promptly to a trailer or towing

vehicle.

NOTICE:

If water isn't removed promptly from a submerged ATV, rust will form in precision

components, gears, bearings, the cylinder and other areas and result in serious engine

damage. Always see your dealer promptly after an ATV has been submerged.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands