Polaris 2010 OUTLAW 450 MXR Page 67 Owner'S Manual Download

Page: 67 / 212

Operation

Safe Operation Practices

8. Drive in a manner appropriate for your

skills and operating conditions. Never

operate at excessive speeds. Never

attempt wheelies, jumps, or other stunts.

Never remove your hands from the han-

dlebars while operating, and always

keep both feet on the footpegs.

9. Never consume alcohol or drugs before

or while operating an ATV.

10. Always use the size and type of tires

specified for your vehicle. Always

maintain proper tire pressure.

11. Never operate a damaged ATV. After

any overturn or accident, have a quali-

fied service dealer inspect the entire

machine for possible damage.

12. Never operate the ATV on a frozen

body of water.

13. Do not touch hot exhaust system com-

ponents. Always keep combustible

materials away from the exhaust sys-

tem.

14. Always remove the ignition key when

the vehicle is not in use to prevent unau-

thorized use.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands