Polaris 2010 OUTLAW 450 MXR Page 110 Owner'S Manual Download

Page: 110 / 212

106

Maintenance

Engine Oil Change

Changing Oil Filters

1. Place a drain pan under the engine.
2. Remove the four oil filter cover screws (1).

Remove the covers.

3. Using circle clip (snap ring) pliers, pull the

oil filter inserts (2) out of the housing.

4. Thoroughly clean the engine casing, filter

covers and sealing surfaces of the O-rings.

Check the O-rings. If damaged, install new

O-rings.

5. Fill each oil filter with oil. Install the long

filter at the front of the filter box. Install the

short filter at the rear of the box.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands