Polaris 2010 OUTLAW 450 MXR Page 146 Owner'S Manual Download

Page: 146 / 212

142

Maintenance

Brakes

Under normal operation, the diaphragm extends into the reservoir as fluid level drops. If the

fluid level is low and the diaphragm is not extended, a leak is likely and the diaphragm

should be replaced. To ensure proper diaphragm operation, always fill the reservoir as

needed whenever the cover is loosened or removed. Do not overfill.

WARNING!

An over-full master cylinder may cause brake drag or brake lock-up, which could result in

serious injury or death. Maintain brake fluid at the recommended level. Do not overfill.

Both brakes are self-adjusting, but the following checks are recommended to keep the brake

systems in good operating condition. Check more often if brakes are used heavily under nor-

mal operation.

Summary of Contents for 2010 OUTLAW 450 MXR





















































































































































































































Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands

Polaris 2010 OUTLAW 450 MXR, Owner'S Manual

Search results

Summary of Contents for 2010 OUTLAW 450 MXR

Reviews:

Related manuals for 2010 OUTLAW 450 MXR

Brands by name

Popular brands