Oracle SPARC Enterprise M3000 Reference Manual Download Page 364 | Manualshive

Page: 364 / 552

background image

showcodusage(8)

346

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised July 2010

EXTENDED

DESCRIPTION

The

showcodusage -p resource

command displays the following COD usage

information for the system:

The

showcodusage -p domain

command displays the following COD usage

information for each domain:

Resource

Identifies the type of COD resources available (processors).

In Use

Specifies the number of COD CPUs currently used in the
system.

Installed

Specifies the number of COD CPUs installed in the system.

COD Permitted

Specifies the number of COD permits installed.

Status

Specifies one of the following COD attributes:

OK

Indicates that there are sufficient permits
for the COD CPUs in use, and displays the
number of COD CPUs that are available,
and the number that can be used to
provide headroom.

HEADROOM

The number of instant access COD CPUs
in use providing headroom.

Violation

Indicates a COD permit violation exists.
Displays the number of COD CPUs in use
that exceeds the number of COD permits
available. This situation can occur when
you force the deletion of a COD key from
the COD Hardware Activation database,
but the COD CPU associated with the key
is still in use.

Domain/Resource

Identifies COD resource (processor) for each domain. An
Unused processor is a COD CPU that has not yet been
assigned to a domain.

In Use

Specifies the number of COD CPUs currently used in the
domain.

«
...
362
363
364
365
366
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

DocuPrint 100MX

Brand: Xerox Pages: 2

Transport GT26-B4987

Brand: TYAN Pages: 125

SUPERSERVER 5018D-MF

Brand: Supero Pages: 120

Brand: Atop Pages: 2

Brand: PRG Pages: 50

PRIMERGY PG-RSBOP2

Brand: Fujitsu Pages: 68

SPARC Enterprise T5440 Server

Brand: Fujitsu Pages: 92

SPARC Enterprise T5140

Brand: Fujitsu Pages: 138

SPARC Enterprise T5440 Server

Brand: Fujitsu Pages: 214

SPARC Enterprise T5140

Brand: Fujitsu Pages: 130

Brand: Fujitsu Pages: 514

Compaq AlphaServer DS10

Brand: HP Pages: 43

Cluster Platform Hardware Kits v2010

Brand: HP Pages: 12

Brand: HP Pages: 12

hpe proliant dl20 gen9

Brand: HP Pages: 131

Cisco MDS 8/12c

Brand: HP Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands