Oracle SPARC Enterprise M3000 Reference Manual Download Page 275 | Manualshive

Page: 275 / 552

background image

setpowerupdelay(8)

System Administration

261

NAME

setpowerupdelay - set the warm-up time of the system and wait time before system
startup

SYNOPSIS

setpowerupdelay

-c warmup -s

time

setpowerupdelay

-c wait -s

time

setpowerupdelay

-h

DESCRIPTION

The

setpowerupdelay

(8) command sets the warm-up time of the system and wait

time before system startup.

The wait time before system startup can be used to control the system startup time
so that the system is started only after air-conditioning makes the temperature of
the computer room suitable. If the system power has already been turned on and
the system is operating, the setting takes effect at the next startup.

Privileges

You must have

platadm

or

fieldeng

privileges to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

EXTENDED

DESCRIPTION

■

You can use the

showpowerupdelay

(8) command to check the warm-up time

and the wait time before system startup, previously set by the

setpowerupdelay

(8) command, regardless of whether the system is in

operation.

■

When the power is turned on from the operator panel, the wait time and warm-
up time that you set are ignored. If you have set these times and wish to observe
them at startup, perform the

poweron

(8) command.

EXAMPLES

EXAMPLE 1

Sets the warm-up time to 10 minutes.

-c warmup

Specifies the warm-up time.

-c wait

Specifies the wait time before system startup.

-h

Displays usage statement. When used with other options or
operands, an error occurs.

-s

time

Specifies the warm-up time or wait time before system startup in
minutes. An integer ranging from 0 to 255 can be specified for
time.

XSCF>

setpowerupdelay -c warmup -s 10

«
...
273
274
275
276
277
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: Gateway Pages: 138

Brand: IBM Pages: 88

RS/6000 7043 43P Series

Brand: IBM Pages: 322

System x3400 M3 Types 7378

Brand: IBM Pages: 45

BACnet/IP Server-SUNWAYS

Brand: IntesisBox Pages: 5

Brand: Gigabyte Pages: 2

Brand: 3Com Pages: 122

TERASTATION HS-D1.0TGL/R5

Brand: Buffalo Pages: 2

ConnectPort LTS 16

Brand: Digi Pages: 169

ProLiant MicroServer

Brand: HP Pages: 22

ProLiant MicroServer Gen8

Brand: HP Pages: 104

ProLiant DL560 Generation9

Brand: HP Pages: 57

ProLiant MicroServer Generation 8

Brand: HP Pages: 36

ProLiant DL585 G7

Brand: HP Pages: 126

ProLiant ML310e Gen

Brand: HP Pages: 92

Brand: HP Pages: 40

ProLiant DL580 G7

Brand: HP Pages: 130

ProLiant DL580 Gen9

Brand: HP Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands