Oracle SPARC Enterprise M3000 Reference Manual Download Page 217

Page: 217 / 552

setemailreport(8)

System Administration

203

NAME

setemailreport - set up the email report configuration data

SYNOPSIS

setemailreport

[

-v

] [

-t

]

setemailreport

[

-s

variable

value

]...

setemailreport

-h

DESCRIPTION

setemailreport

(8) sets up email reporting configuration data for remote

maintenance. Once the configuration data is set up, it is used by the fault
management daemon to send email reports as required.

If you run the

setemailreport

command without specifying any options, you

will be prompted to answer whether email reporting is to be enabled. If enabled,
you will be prompted to provided a list of email addresses.

Where:

You can set up email reporting noninteractively by using the

-s

option.

After the email server and port have been set up using

setsmtp

(8), you can use

setemailreport -t

to send a test email message.

Privileges

You must have

platadm

privileges to run this command.

Refer to

setprivileges

(8) and for more information.

-a

Add recipient

-d

Delete recipient

-r

Replace recipient (Default)

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands