Oracle SPARC Enterprise M3000 Reference Manual Download Page 352 | Manualshive

Page: 352 / 552

background image

showboards(8)

336

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised July 2010

When the

-v

option is specified, the following types of information are displayed

as XSB detail status information:

Conf

Incorporation state of XSB hardware resources into the Solaris OS

n

The resources are not connected to the Solaris
OS.

y

The resources are incorporated in the Solaris
OS.

Test

Status of an initial diagnosis on an XSB

Unmount

The XSB cannot be recognized because it is
not mounted or because it has an error.

Unknown

Not performed.

Testing

The initial diagnosis is in progress.

Passed

The initial diagnosis ended normally.

Failed

Error (test=fail) detected by an initial
diagnosis. The XSB cannot be used or is in a
degraded state.

Fault

XSB degradation status

Normal

Normal

Degraded

Component in a degraded state. The XSB
can operate.

Faulted

An error occurred and the XSB cannot
operate.

R

Dynamic reconfiguration(DR) involving the reservation state of
the XSB in the domain

*

DR processing is reserved. When the domain
is rebooted, the XSB is incorporated into or
disconnected from the domain, and the
domain configuration is changed.

Cod

Whether the XSB is a COD board

n

The XSB is not a COD board.

y

The XSB is a COD board.

«
...
350
351
352
353
354
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: Hanwha Pages: 3

Brand: IBM Pages: 74

UniServer R4300 G5

Brand: H3C Pages: 16

eServer BladeCenter HS40 Type 8839

Brand: IBM Pages: 120

SUPERSERVER 5018A-MHN4

Brand: Supermicro Pages: 116

FusionServer G5500 V6

Brand: xFusion Digital Technologies Pages: 100

System X Series

Brand: IBM Pages: 6

Brand: LOOQS Pages: 69

VIP Media Server Pro

Brand: Chauvet Pages: 20

IP-DECT SERVER 6500

Brand: SpectraLink Pages: 126

Brand: DNP Pages: 136

Brand: Black Box Pages: 4

Brand: Black Box Pages: 12

Brand: Lindy Pages: 2

DIRECTORY SERVER 7.1

Brand: Red Hat Pages: 652

Proline Promass 300 EtherNet/IP

Brand: TechnipFMC Pages: 36

Brand: Supero Pages: 130

Brand: SAFARI Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands