Oracle SPARC Enterprise M3000 Reference Manual Download

Page: 23 / 552

addboard(8)

System Administration

■

When the command is executed, a prompt to confirm execution of the command
with the specified options is displayed. Enter "

" to execute the command or "

to cancel the command.

■

If "

-c configure

" is specified when either the domain power has been turned

off or the Solaris OS is not running, an error occurs.

■

When "

-c configure

" is specified, hardware diagnosis is performed on the XSB

before it is incorporated into the domain. Therefore, command execution may
take time.

■

To use the

addboard

(8) command to configure or assign an XSB, DCL must be

set up in advance using the

setdcl

(8) command.

■

If the

addboard

(8) command is executed under the progress of power-on or

power-off processing, the busy status is returned. After that processing in the
domain is completed, reexecute the command.

■

See the

setdcl

(8) and

showdcl

(8) commands for DCL.

EXAMPLES

EXAMPLE 1

Configures XSB#00-0, #01-0, #02-0, and #03-0 into domain ID 0.

EXAMPLE 2

Configures XSB#00-0, #01-0, #02-0, and #03-0 forcibly into domain ID 2.

EXIT STATUS

The following exit values are returned:

SEE ALSO

deleteboard

(8)

moveboard

(8)

replacefru

(8)

setdcl

(8)

setdomainmode

(8)

setupfru

(8)

showboards

(8)

showdcl

(8)

showdevices

(8)

showdomainstatus

(8)

showfru

(8)

testsb

(8)

XSCF>

addboard -y -c assign -d 0 00-0 01-0 02-0 03-0

XSCF>

addboard -f -d 2 00-0 01-0 02-0 03-0

Successful completion.

An error occurred.

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands