Oracle SPARC Enterprise M3000 Reference Manual Download Page 13

Page: 13 / 552

Intro(8)

Intro

NAME

Intro - list the commands provided by the XSCF firmware

DESCRIPTION

Intro

(8) command lists the commands provided by the XSCF firmware of the

SPARC Enterprise™ M3000/M4000/M5000/M8000/M9000 servers.

Some commands are used in a different way or not supported on your server. For
details, refer to the pages of each command.

LIST OF

COMMANDS

In XSCF, the following commands are provided:

Intro

intro

list the commands provided by the XSCF firmware

addboard

configure an eXtended System Board(XSB) into the domain
configuration or assigns it to the domain configuration

addcodactivation

add a Capacity on Demand (COD) activation key to the
COD Hardware Activation database

addcodlicense

add a Capacity on Demand (COD) right-to-use (RTU)
license key to the COD license database

addfru

add a Field Replaceable Unit (FRU)

adduser

create an XSCF user account

applynetwork

apply XSCF network information to the XSCF

cfgdevice

connect a CD-RW/DVD-RW and TAPE drive unit to the
port, disconnect it from the port, or display the status of the
drive

clockboard

set or display the clock control unit used at system startup

console

connect to a domain console

deleteboard

disconnect an eXtended System Board (XSB) from the
domain configuration

deletecodactivation

remove a Capacity on Demand (COD) activation key from
the COD Hardware Activation database

deletecodlicense

remove a Capacity on Demand (COD) right-to-use (RTU)
license key from the COD license database

deletefru

delete a Field Replaceable Unit (FRU)

deleteuser

delete an XSCF user account

disableuser

disable an XSCF user account

dumpconfig

save system configuration information to a file

enableuser

enable an XSCF user account

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands