Oracle SPARC Enterprise M3000 Reference Manual Download Page 326 | Manualshive

Page: 326 / 552

background image

setupfru(8)

310

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised November 2009

OPERANDS

The following operands are supported:

EXTENDED

DESCRIPTION

■

In the M8000/M9000 server, the Quad-XSB configuration cannot be set in
memory mirror mode.

■

To set up an already mounted PSB again, all XSBs comprising the target PSB
must have been disconnected from the domain configuration and placed under
the system board pool. See the

deleteboard

(8) command for information on

how to disconnect XSBs from the domain configuration.

■

The configuration of the PSB varies according to the system as shown below.

■

In the M8000/M9000 servers, the PSB consists of one CPU/memory board
unit and one I/O unit in combination.

■

In the M4000/M5000 servers, the PSB consists of one CPU module and one
memory module logically divided into two on the motherboard unit, and one
I/O module.

■

Although a CMU with two CPUs can be configured into Quad-XSB mode on an
M8000/M9000 server, the server generates a "configuration error" message for
those XSBs that do not have a CPU and memory.

■

The current PSB settings can be checked by using the

showfru

(8) command.

EXAMPLES

EXAMPLE 1

Configures PSB#00 as a Quad-XSB (with memory in non-mirror mode be-
cause the memory mirror mode setting is omitted).

EXIT STATUS

The following exit values are returned:

SEE ALSO

addboard

(8)

,

deleteboard

(8)

,

moveboard

(8)

,

setdcl

(8)

,

showboards

(8)

,

showdcl

(8)

,

showdevices

(8)

,

showfru

(8)

device

Specifies the device to be set up. Only the following device can be
specified:

sb

Physical system board (PSB)

location

Specifies the location of the device.

sb

Integer from 0–15. Specify only one

location

.

XSCF>

setupfru -x 4 sb 0

0

Successful completion.

>0

An error occurred.

«
...
324
325
326
327
328
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Express5800/T110g-S

Brand: NEC Pages: 34

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Lantronix Pages: 10

Brand: Lantronix Pages: 17

Brand: Lantronix Pages: 109

Brand: Lantronix Pages: 24

Brand: Lantronix Pages: 29

Brand: Lantronix Pages: 2

Flex System x240 Compute Node

Brand: IBM Pages: 28

Brand: Oki Pages: 2

Brand: SMC Sierra Monitor Pages: 42

Brand: NAIM Pages: 18

Brand: Buffalo Pages: 2

Brand: IBM Pages: 10

Brand: Avaya Pages: 119

Brand: Portwell Pages: 21

Brand: Conceptronic Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands